This is amazing...

Although it's not Corvette-related, it's still an amazing piece of video.

DIC codes

At some point in your Corvette experience, you're going to need to find out what type of error occurred in your engine that caused your "Check Engine" light to come on.

It could something as simple as a loose fuel cap, or it may be something more serious that needs attention. In case that's happened to you, here's an easy way to see where the problem originated.

In the center of your instrument panel, below the speedometer and tach, there is a horizontal readout that comes one when you start the car. It usually begins with the word "CORVETTE" and then changes to "BY CHEVROLET." This is what is referred to as your DIC, or Digital Information Center.

Turn the ignition key on, but don't start the car. Hold down the OPTIONS button and press the FUEL button four times. You're now in DIAGNOSTIC MODE.

The computer will display what are referred to as DTCs or Diagnostic Trouble Codes. There are two kinds of DTCs, "Current" and "History," designated with a letter suffix, "C" or "H". A current code indicates that the malfunction is present in the system whose module is displaying data. A history code indicates a problem existed in that module sometime in the last 40 or 50 ignition cycles. When not accompanied by a current code of the same number, it is possible it's evidence of a previous problem, now solved, that was not removed by clearing codes. More likely is that a history code indicates an intermittent malfunction. "Intermittents" are the most challenging DTCs. An intermittent may have happened only once, may have happened more than once but is inconsistent in its appearance or may be happening on a regular basis but not at the time the IPC is displaying codes.

History codes can also be caused by a current malfunction in a system that is not operating at the time DTCs are displayed. An example is the rear window defogger which doesn¹t operate until the BCM detects engine rpm. For history codes set by a system that does not operate with the key on and engine off, a special diagnostic tool called a "scan tester" is necessary to properly diagnose the malfunction.

Inititially, the on-board diagnostics go into the "automatic" mode which shows each module's DTCs in a pre-set sequence:

10 PCM Powertrain Control Module
28 TCS Traction Control system ABS
?? RTD Real Time damping
40 BCM Body Control Module
60 IPC Instrument Panel Cluster
80 radio
99 HVAC Heater Vent-Air Conditioning
A0 LDCM Left Door Control module
A1 RDCM Right Door Control Module
AC SCM Seat Control module
B0 RFA Remote Function Actuation

For each module, all DTCs will be displayed. If none are present in a module, you will see "no more codes" on the ICP display.

Once the IPC has displayed all 11 modules, the system goes into the manual mode which allows selection of each module using combinations of DIC buttons. The manual mode can also be entered at any time during the automatic sequence by pressing any button except "E/M". Once the IPC displays "manual diagnostics," you may select a particular module by pressing the "options" button to go forward or the "trip" button to go back. Once a system is selected and a DTC is displayed, if more than one are present; press "gages" to move forward or "fuel" to go back.

To exit the diagnostic mode at any time, press "E/M". If you want to erase or "clear" codes, press "reset." Clearing a code does not repair a problem. You are simply erasing the evidence of it in the module's memory.

So, now that you have the codes, what do they mean? Rather than list them all here, I'm going to refer you to another site. This site provides a great listing of all the error codes you may encounter. http://www.stengel.net/diccodes.htm.

Hope that helps.

Stingray Concept Design Overview

Now let's jump forward to today and take a look at this concept design for the Stingray. Pretty impressive.

Blue Devil vs Blue Angel

If you love speed, this is the video you've been waiting for.

Jim Mero Driving the ZR1

If you're up for a little adrenaline rush, hop in the passenger seat and strap in. This is an exciting ride at Nurburgring when Jim drove the 7:26.4 record lap. Hang on because it's a great ride in a great car.

Enjoy!

How do those nannies work?

Active Handling was introduced by GM in 1998 as an option. It became standard equipment on the 2001 and newer models. Like me, there may be a few of you who don’t realize what it does, how it does it, and the other options you have in changing the features. I’m not recommending you disengage it, but I thought you might like to know the options. Following is an abbreviated version of a GM Press Release from the fall of 1998. If you would like to read the full press release, this link will take you there: http://www.corvetteactioncenter.com/tech/c5/activehandling.htmltivehandling.html

What Active Handling Does

The Active Handling system activates when there is a significant difference between how the driver intends for the car to corner and how the car is actually cornering. Working together with the ABS and traction control systems as needed, it automatically applies any of the four brakes to help correct the situation

Active Handling uses a simple yet sophisticated system of sensors to detect unwanted vehicle manuevers. These sensors include a steering angle sensor, yaw-rate sensor, lateral accelerometer and sensors in the vehicle's ABS brake and traction control systems. All of the data that these sensors provide is fed into the Corvette's onboard computer where specially-developed software "reads" all of the inputs and automatically activates the car's brakes selectively to help the driver bring the vehicle back under control.

Steering Angle Sensor: This digital sensor monitors the driver's steering inputs immediately and communicates the steering angle that the driver has selected back to the system. It is accurate to within one degree of steering angle change and is located in the car's steering column.

Yaw-Rate Sensor: This solid-state device utilizes a tiny pair of ceramic tuning forks to measure the actual rate that the car is turning or yawing from the centerline. This data is continuously fed into the Corvette's computer where the yaw rate is compared to the steering angle. Any variation beyond a pre-programmed set of values will result in activation of the Active Handling system's assist features. The yaw-rate sensor on the Corvette is located inside the center console.

Lateral Accelerometer: The lateral acceleration sensor measures the centrifugal force created in a turn. The data it provides is weighed against all of the other inputs and is used to calculate whether or not the car's limits are being exceeded for the speed and traction conditions that exist. This sensor is located beneath the passenger seat.

Unique Controller & Software: All of the information being provided by the sensors mentioned above is processed by the Corvette Active Handling system's computer through a very sophisticated and specialized software package. This computer is actively linked to the ABS brake system and the traction control system -- all these systems share information continuously. This multiple linkage is vital because the combined inputs from each system make the fully-integrated system better able to respond to a wider variety of inputs from the driver.

Competitive Driving Mode

The Corvette Active Handling system will be the first of its type to offer dual mode operation. In addition to an "OFF" mode, in which Active Handling is disabled, the system also allows the driver to select a "COMPETITIVE DRIVING" mode for autocross or gymkhana competitions. In this mode, the Active Handling system remains fully-functional -- measuring steering, yaw rate and lateral acceleration inputs as well as applying individual wheel brakes as required -- but the traction control system is disabled, allowing for some wheelspin and oversteer that skilled drivers often find beneficial in competitive driving.

Summary of Active Handling System Modes

ON - Active Handling is automatically enabled when the car is started. This is also true of the ABS brake and traction control systems.

OFF - Like traction control, the Active Handling system may be manually turned off if the driver so desires. This is not true of the ABS brake system which is always enabled.

COMPETITIVE DRIVING - In this mode, Active Handling and ABS are both enabled, but traction control is shut off.

The "OFF" and "COMPETITIVE DRIVING" modes are important features on a high-performance sports car like the Corvette. As mentioned earlier, skilled drivers may find that some wheelspin and oversteer can be beneficial to their lap times in competitive events, and the Corvette system allows them to operate the car in this fashion when appropriate. Chevrolet recommends against selecting these modes for street use.

Limitations

The overall effectiveness of the Corvette Active Handling system, or any similar system, is directly related to available tire traction and the aggressiveness of a given maneuver. Active Handling is designed to work to use existing traction to assist the driver -- but it cannot overcome the laws of physics. The Active Handling system reacts only in extreme situations, and special care should be taken when the system does activate because it's a clear signal that vehicle or tire limits are being exceeded.

This information wasn't placed on this site to encourge anyone to drive without the Active Handling system turned on. The Corvette is a powerful car, and a system of this type can be beneficial in preventing out-of-control situations from remaining that way.

Corvette vs Ferrari... Fun Stuff.

I found this interesting and exciting. What fun. I'm going to go out later today and find me a Ferrari to beat up on.

How to use a claybar...

Some of our readers have asked about claybarring. This is one of the easiest and most important first steps in giving your pride and joy a beautiful shine. Naturally, you would follow the clay bar procedure with your polishing and waxing processes. We'll talk aobut those in a future post.

From experience, I can tell you the most important part is to use ample wetting agent to prevent the clay from sticking to the paint. It won't cause any damage if this happens but makes it a bit difficult to get it loose. Not a bit deal, but easily prevented.

Enjoy.

Not Corvette, but Worth Seeing...

This video is from the Volkswagen plant in Dresden, Germany. It was sent to me by my good friend, Pat, from Indiana. It's amazing and something that the UAW ought to consider for improving conditions, quality, and morale.

Enjoy.

Love that Meguiar's

Summer has arrived and it's time to keep that Corvette sparkling and shiny with a good coat of wax. I know each of you has your favorite detailing products. Or maybe you don't, and you're looking for suggestions. Well, here's mine. I love Meguiar's products. They make everything I need for giving my Vette a deep, lustrous shine and protecting it from the elements.

Here's my procedure:

Since I don't drive my Vette in the rain (yes, I'm one of those guys) I rarely need to wash it. When I'm not driving it, it stays protected in my garage under its car cover. But it still needs some care on a regular basis to keep that shine going on.

My first step when I bought the car was to use a claybar. You may not think it's necessary, but I assure you it will make a difference in the depth of the shine you can achieve. The secret is not to scrimp on spraying that lubricating spray. Otherwise your claybar will stick to the paint. No damage, but just a little troublesome to get it unstuck.

Secondly, I use Meguiar's Step 2 Polish. You apply it like wax. And here's a point I'm adamant about. Always use a microfiber towel unless you want to end up with swirls in the paint.

After Meguiar's Step 2 Polish, I apply the Meguiar's Showcar Glaze. Same procedure. And I finish it off with Meguiar's Gold Class Wax. That's it. I'm done. I do the whole car by hand.

So enjoy polishing your Vette, no matter what product you prefer. Just remember to use those microfiber towels.

You'll be happy you did.

Watch those potholes!

One thing you have to be very careful of when driving a Corvette, or any other sports car that sits close to the ground, is potholes.

Actually, you need to be careful in any vehicle when it comes to holes in the road surface, especially at higher speeds.

Here are a couple that appear to be quite dangerous and capable of inflicting serious damage to your undercarriage.

I don't know about you, but I know this would slow me down! I see myself slowing down, trying to "straddle" the hole, then breathing again when I cleared it without hitting it!

But they're not really holes. They're actually a clever, new idea to slow traffic down. Actually much better than the old concrete or asphalt humps or speed bumps we all remember. It looks like these would jar your dentures loose if you drove into one.

So if you're driving along and see something that looks like anything in these pictures, just be careful. If you think they're the fake ones you've seen on here, and just drive carelessly over them, you might be surprised.

It could be the real thing.

ENTER TO WIN TWO CORVETTES!

That's right. Not one, but TWO Corvette's are being given away. Plus you can help deserving kids in the process.

CLICK HERE to enter.